{"product_id":"blikvm-hat-remote-control-server-pikvm-operation-maintenance-kvm-remote-control","title":"BliKVM Hat Remote Control Server Pikvm Operation Maintenance Kvm Remote Control","description":"\u003cp\u003e\u003cspan\u003eBliKVM V3 HAT remote control blikvm server operation and maintenance kvm remote control pikvm operation and maintenance overip\u003cbr\u003e\u003cbr\u003eIntroduction to PiKVM:\u003cbr\u003ePiKVM is a remote management solution based on open source software and hardware technology. It can remotely connect to the computer through the Raspberry Pi, turn on\/off or restart the computer. Configure UEF I\/BIOS or even reinstall the operating system using a virtual CD-ROM or flash drive. You can use Remote Keyboard and Mouse to emulate a keyboard, mouse, and monitor and then display them in a web browser as if you were working directly on the remote system. This is true hardware-level access and does not rely on any remote port, protocol or service!\u003cbr\u003e\u003cbr\u003eBliKVM Hat product introduction:\u003cbr\u003eThe BliKVM Hat version is a piece of hardware based on Raspberry Pi 4B and is used for KVMOverIP. Hat's key functions include HDMI video capture, ATX control, PoE power supply, OLED screen display, and RTC clock. Hat comes with a metal shell for protection and heat dissipation. Hat can be installed into a 1U rack. Supports both blikvm mirror and pikvm mirror.\u003cbr\u003e\u003cbr\u003eAccessories introduction:\u003cbr\u003eATX module\u003cbr\u003eThe ATX module is connected to the computer's motherboard via a DuPont cable.\u003cbr\u003eATX modules come with full-height and half-height PCle bezels.\u003cbr\u003eUSB\/PWR distribution board\u003cbr\u003eThe RPI4 port is used to connect to the Raspberry Pi 4B.\u003cbr\u003eThe USB port is used to connect to the controlled computer.\u003cbr\u003eWhen using PoE power supply, there is no need to use a distribution board.\u003cbr\u003eHDMI simulator\u003cbr\u003eIf the controlled computer cannot output the screen correctly, you can try to use this module to solve the problem. After connecting this module to the Hat, connect it to the controlled computer through an HDMI cable.\u003cbr\u003eUSB\/PWR distribution board\u003cbr\u003eThe metal shell can protect the Hat and be used for heat dissipation. Each port on the shell has a clear silk screen to indicate the purpose of this port. This enclosure can be easily installed in a 1U rack.\u003cbr\u003e\u003cbr\u003eHardware details:\u003cbr\u003eHDMI input\u003cbr\u003eThe bridge chip is Toshiba TC358743, which supports both video and audio (I2S). The maximum input resolution is 1080p@50fps. Fixed HDMI reverse power issue.\u003cbr\u003eCN-ATX\u003cbr\u003eThe CN-ATX interface is connected to the ATX adapter board (accessory to HAT) through a network cable, which can turn on, off and restart the controlled computer.\u003cbr\u003eshow\u003cbr\u003eWhite OLED display with 128x32 resolution and SSD1306 chip. This display can display the temperature, IP address and other information of the Raspberry Pi.\u003cbr\u003ePOE\u003cbr\u003eStandard: IEEE 802.3af PoE Input voltage: 37-57VDC Output power: 5VDC\/2.4 A\u003cbr\u003ePlug in the PoE jumper cap and enable the PoE power supply\u003cbr\u003efan\u003cbr\u003eThe IPKVM HAT houses a small fan that is controlled by your Raspberry Pi via GPIO12.\u003cbr\u003eReal Time Clock\u003cbr\u003eThe clock chip is a PCF8563 and is controlled by your Raspberry Pi via I2C. The coin-shaped battery is installed under the HDMIIN module.\u003cbr\u003e\u003cbr\u003ePackage Included:\u003cbr\u003e1x Raspberry Pi IPKVM HAT\u003cbr\u003e1x ATX adapter board\u003cbr\u003e1x USB\/PWR splitter\u003cbr\u003e1x HDMI pass-through EDID emulator\u003cbr\u003e1x metal case\u003cbr\u003e1x 32G TF card\u003cbr\u003e1x USB Type-C to USB Type-C cable\u003cbr\u003e1x Dupont cable 8PIN male to male 40cm\u003cbr\u003e1x Dupont cable 8PIN male to female 40cm\u003cbr\u003e1x Phillips screwdriver\u003cbr\u003e1x Phillips wrench socket\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eWarranty:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eReturns: Customers have the right to apply for a return within 60 days after the receipt of the product\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e24-Hour Expert Online: Solve your installation and product problems\u003c\/span\u003e\u003c\/p\u003e","brand":"CarLightBulb","offers":[{"title":"Default Title","offer_id":44531890225314,"sku":"E201-A116","price":147.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0463\/7012\/8034\/files\/07ca2a21f2c97726a265a60c14e6b59d.jpg?v=1716270507","url":"https:\/\/carlightbulb.com\/it-it\/products\/blikvm-hat-remote-control-server-pikvm-operation-maintenance-kvm-remote-control","provider":"CarLightBulb","version":"1.0","type":"link"}